Commercial Rigid Sewage Pump Single Stage With Teco Motor High Performance
| Place of Origin: | Zhejiang, China (Mainland) |
|
|
| Add to My Favorites | |
| HiSupplier Escrow |
Product Detail
Commercial Rigid Sewage Pump Single Stage With Teco Motor High Performance
<
Commercial Rigid Sewage Pump Single Stage With Teco Motor High Performance
Features:
| 1 | The leakage detector offers pump an automatic protection |
| 2 | Not stamdard accessories, the power not lower than 18.5KW is optional |
| 3 | Built-in heat protector in motor, it secures the protection of motor against burning out. |
| 4 | The power not lower than 18.5KW is optional |
| 5 | Well statically & dynamically balanced Non-Clog impeller is designed to allow sizable spherical solids to pass the plow passage easily without clogging.It adopts rigorous technics so that vibration and noise can be farthest reduced. |
Application:
| 1 | Pasturage drainage. |
| 2 | Cabin ponding . |
| 3 | Civil and architectural engineering construction. |
Points for attention before starting equipment:
-
Check whether the power and the voltage frequency used are in line with those listed on the label.
-
Check whether the grounding wire is earthed properly.
-
Operation without water is prohibited.
-
Submerging cable sockets of the motor into water is prohibited.
Warning:The water pump shall not be moved without putting off the power source. Humans shall not contact the water source where the pump is located when pumping water to prevent electric shock accidents in case there is no current leakage protective device while there is current leakage with the pump.
Read this Installation, Operation and Maintenance Manual carefully to guarantee the safe operation of the equipment.
The safety notice in the manual includes warning and points for attention:
-
Warning means possible dangers, which may cause human loss or serious injury etc if ignored.
-
Points for attention mean possible dangers, which may cause slight or moderate injuries of humans or equipments if not removed.
Construction:
| No. | Name | Material | |
| GB | JIS | ||
| 1 | Neck bolt | 2Cr13 | SUS420 |
| 2 | Heat-Protector | - | - |
| 3 | Motor cover | HT200 | FC200 |
| 4-1 | Bearing | - | - |
| 4-2 | Bearing | - | - |
| 5 | Cooling house flange | Q215A | LSS330 |
| 6 | Shaft | 2Cr13 | SUS420 |
| 7 | Rotor | - | - |
| 8 | Stator | - | - |
| 9 | Cooling house | 0Cr18Ni9 | SUS304 |
| 10 | Bearing cover | HT200 | FC200 |
| 11 | Motor casing | HT200 | FC200 |
| 12 | Bracket | HT200 | FC200 |
| 13 | Leakage detector | - | - |
| 14-1 | Mechanical seal | C-Al2O3 | C-Al2O3 |
| 14-2 | Mechanical seal | SiC-SiC | SiC-SiC |
| 15 | Oil box | HT200 | FC200 |
| 16 | Oil cover | HT200 | FC200 |
| 17 | Washer | 0Cr18Ni9 | SUS304 |
| 18 | Impeller nut | HT200 | FC200 |
| 19 | Seal-ring | LBC2 | LBC2 |
| 20 | Strainer | HT200 | FC200 |
| 21 | Impeller | HT200 | FC200 |
| 22 | Pump casing | HT200 | FC200 |
| 23 | Bottom cover | HT200 | FC200 |
| 24 | Pall piping | Q215A | SS330/SS34 |
| 25 | Flange setter | HT200 | FC200 |
| 26 | Slide | HT200 | FC200 |
