DIN 24255 Hydraulic Single Suction Centrifugal Pump End Suction Capacity 1660 m3/h GHS manufacturer from China GSD Industrial Co., Ltd.

DIN 24255 Hydraulic Single Suction Centrifugal Pump End Suction Capacity 1660 m3/h

Place of Origin:

Zhejiang, China (Mainland)


	Add to My Favorites
HiSupplier Escrow	Share \|

Product Detail

Model No.: GHS

DIN 24255 Hydraulic Single Suction Centrifugal Pump End Suction Capacity 1660 m3/h

<span st

DIN 24255 Hydraulic Single Suction Centrifugal Pump End Suction Capacity 1660 m3/h

Working condition
a. Outlet: DN32-300mm
b. Capacity: 4.5-1660 m³/h
c, Head: 5.2-150m
d. Motor speed: 1450 rpm & 2900rpm for 50hz ; 1750rpm & 3500 rpm for 60hz.
e. Conveyance medium temperature: -10 to 85
f. Working pressure: 1.6 Mpa is standard, available for up to max working pressure 2.5Mpa.

Application
a. Applied to convey clean liquid
b. For water-supply & drainage for factory
c. For agricultural irrigation

Features
a. Designed by following DIN24255
b. Materials are variable based on customer demand
c. The pump rotates in the colckwise direction if viewed from the driven end
d. The pumps of the same specifications may have different performances (indicated with ABC on pump models) if changed in impeller outer diameters (cutting impeller).
e. Installed with IEC standard motor
f. Painting color & nameplate are accable for OEM

Operation

1	ELECTRIC MOTOR DRIVE	Install a starter with overload protection to prevent the motor being damaged by overload. The overloads should be set so that they trip if the current exceeds the normal current of the motor (see motor nameplate) by 10%.
2	BEFORE STARTING	The pump is ready for starting when: 1) Pump base-plate is grouted and bolted to the foundation. 2) Pump and driver are correctly aligned. 3) Bearing lubrication is provided. 4) Stuffing box has been packed or fitted with seal. 5) Cooling water is supplied to bearing—if specified. 6) Prime mover has been checked for correct direction of rotation. 7) All rotating parts are found free by turning by hand. 8) Pump is primed. Never run a pump dry.
3	RUNNING	While the pump is running, a periodic inspection should be made of: 1) Stuffing-Box: Keep stuffing-boxes (if soft packed, not fitted with mechanical seal) so that there is sufficient leakage to lubricate the package. 2) Bearing: Check the bearing for temperature which should not exceed 70(160°F). Grease nipples are provided for bearing lubrication. 3) Alignment: Successful operation of the pumps depends on accurate alignment. It is recommended to re-check the alignment after preliminary run.
4	STARTING	Start the pump with discharge valve closed and bring it up to speed rapidly. When pressure is reached open discharge valve slowly. Do not operate unit for prolonged periods with closed discharge valve, so as to avoid overheating.

Construction

No.	Pump accessory descripation
1	Pump body
2	Cap nut
3	Pipe plug
4	Impeller flat key
5	Impeller
6	Seal ring
7	Pump cover
8	Pump body O-ring
9	Suspension
10	Water deflector
11	Shaft cap
12	Shaft
13	Bearing
14	Suspension support
15	Pump connection flat key

1) The pump is back exposed design , when open the casing cover and impeller, there is not necessary to dismantle suction pipe and discharge pipe.
2) Bearing house is equipped with bearing. The bearing can be lubricated by oil or grease, and pump is directly driven by motor through the flexible coupling.
3) Volute chamber, feet, inlet flange and outlet flange are castinged as a whole one.

Production line